-
1 снабжён
•Insulated electric conductors are provided with a covering of flexible material.
•Those three amino acids are provisioned (or provided) with six codons each.
•The cell is completed with a reference electrode.
•The instrument is complete with a carrying case.
•The unit is equipped (or furnished, or provided) with a turbocharger.
•The space vehicle is fitted out with a pressurized cabin.
•The cylinder is fitted with a detachable head.
•The chamber is fitted with an opening.
•The element is furnished with a knob.
•The instrument incorporates a safety device.
•The thermocouples are supplied with sheaths.
•Spindle units feature angular contact bearings.
Русско-английский научно-технический словарь переводчика > снабжён
-
2 тонкостенная металлическая труба для электропроводки
тонкостенная металлическая труба для электропроводки
-EN
electrical metallic tubing
A thin-walled metal raceway having a circular cross section; used to pull in or withdraw electric cables or wires after the tubing is installed in place; uses connectors and couplings other than the threaded type.
[ http://www.answers.com/topic/electrical-metallic-tubing-1]
intermediate metal conduit
IMC
-Intermediate metal conduit, or IMC for short, is a rigid steel electrical conduit that is lighter in weight than another rigid conduit. It was designed specifically to protect insulated electrical conductors and cables. It does the work of a similar conduit, galvanized rigid conduit (GRC), but with much less weight and thickness size. By utilizing IMC in areas allowed, you can all but eliminate the need for a heavier wall conduit.
IMC has other advantages over GRC. It has a larger interior diameter than Galvanized Rigid Conduit and the smoother interior of the pipe allows for easier wire pulling through the conduit.
IMC was originally introduced by Allied Tube & Conduit Corporation. It is manufactured in accordance with Underwriters’ Laboratories safety standard 1242 and ANSI C80.6. Believe it or not, Allied claims that IMC is actually more rigid than GRC in applications such as service masts and other installations. It has been installed in industrial and commercial buildings. In fact, the National Electrical Code has a specific article about IMC, article 342.
IMC conduit is coated in a hot galvanized coating on the exterior and a special corrosive-resistant coating on the inside to extend the conduit’s lifespan for reliability. Common conduit sizes range from ½” to 4”.
[ http://electrical.about.com/od/metalpvcconduit/a/IMCconduit.htm]Тематики
- электропроводка, электромонтаж
EN
Русско-английский словарь нормативно-технической терминологии > тонкостенная металлическая труба для электропроводки
-
3 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
4 длительный допустимый ток
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-английский словарь нормативно-технической терминологии > длительный допустимый ток
-
5 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
6 труба для электропроводки
труба
Компонентзащищеннойтрубной электропроводки, имеющий, как правило, круглое поперечное сечение, предназначенный для прокладки изолированных проводов и(или) кабелей в электрических или коммуникационных установках, допускающий их затяжку в него и(или) их замену.
ПримечаниеСоединения труб должны быть достаточно плотными, чтобы изолированные провода и (или) кабели могли быть только затянуты, но не введены сбоку в просвет между трубами.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60050-826-2009]
трубопроводтруба
Закрытый элемент кабельной конструкцииКомпонент трубной электропроводки круглого или иного сечения для прокладки в электрических установках кабелей и/или изолированных проводови/или кабелей в электрических установках,позволяющий производить ихвыемкузатяжку и/или замену.
Примечание
Трубопроводы должны быть закрыты таким образом, чтобы имелась возможность вставлять в них изолированные провода и/или кабели.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
conduit
a part of a closed wiring system of generally circular cross section for insulated conductors and/or cables in electrical or communication installations, allowing them to be drawn in and/or replaced
Source: 826-06-03 MOD
[IEV number 442-02-03]
conduit
part of a closed wiring system of circular or non-circular cross-section for insulated conductors and/or cables in electrical installations, allowing them to be drawn in and/or replaced
NOTE Conduits should be sufficiently close-jointed so that the insulated conductors and/or cables can only be drawn in and not inserted laterally.
[IEV 826-06-03]
[IEC 60204-1-2006]
raceway
A tube that encloses and protects electric wires.
[ http://www.answers.com/topic/raceway]FR
conduit
élément d'un système de canalisation fermé de section droite généralement circulaire, destiné à la mise en place par tirage ou au remplacement des conducteurs ou des câbles isolés dans les installations électriques ou de télécommunication
Source: 826-06-03 MOD
[IEV number 442-02-03]См. также пластмассовые трубы для электропроводок
См. также стальные трубы для электропроводок
4.1. Для прокладки проводов и кабелей необходимо применять специальные трубы для электропроводок: гладкие из непластифицированного ПВХ по ТУ 6-19-215-86, прил. 2; гладкие из вторичного ПЭ по ТУ 63.178-103-85, прил. 3; гладкие из наполненного ПЭ по ТУ 6-19-051-575-85, прил. 4; гофрированные из НПВХ по ТУ 6-19-051-419-84, прил. 5; гофрированные из ПЭ по ТУ 6-19-051-518-87, прил.6; гофрированные из вторичного ПЭ по ТУ 63.178-117-87, прил.7. При отсутствии указанных труб применяют технологические трубы: гладкие напорные из НПВХ по ТУ 6-19-231-87, прил.8; гладкие напорные из ПЭ низкого и высокого давления по ГОСТ 18599-83, прил. 9; гладкие из ПП по ТУ 38-102-100-76, прил. 10; трубы из вторичного ПЭ по ТУ 6-19-133-79, прил. П.
...
4.3. Применяют также трубы стальные электросварные по ГОСТ 10704-76 сортамент, прил. 12, легкие и обыкновенные водогазопроводные по ГОСТ 3262-75*, прил.13.[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]
Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- электропроводка, электромонтаж
Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > труба для электропроводки
-
7 труба для электропроводки
труба
Компонентзащищеннойтрубной электропроводки, имеющий, как правило, круглое поперечное сечение, предназначенный для прокладки изолированных проводов и(или) кабелей в электрических или коммуникационных установках, допускающий их затяжку в него и(или) их замену.
ПримечаниеСоединения труб должны быть достаточно плотными, чтобы изолированные провода и (или) кабели могли быть только затянуты, но не введены сбоку в просвет между трубами.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60050-826-2009]
трубопроводтруба
Закрытый элемент кабельной конструкцииКомпонент трубной электропроводки круглого или иного сечения для прокладки в электрических установках кабелей и/или изолированных проводови/или кабелей в электрических установках,позволяющий производить ихвыемкузатяжку и/или замену.
Примечание
Трубопроводы должны быть закрыты таким образом, чтобы имелась возможность вставлять в них изолированные провода и/или кабели.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
conduit
a part of a closed wiring system of generally circular cross section for insulated conductors and/or cables in electrical or communication installations, allowing them to be drawn in and/or replaced
Source: 826-06-03 MOD
[IEV number 442-02-03]
conduit
part of a closed wiring system of circular or non-circular cross-section for insulated conductors and/or cables in electrical installations, allowing them to be drawn in and/or replaced
NOTE Conduits should be sufficiently close-jointed so that the insulated conductors and/or cables can only be drawn in and not inserted laterally.
[IEV 826-06-03]
[IEC 60204-1-2006]
raceway
A tube that encloses and protects electric wires.
[ http://www.answers.com/topic/raceway]FR
conduit
élément d'un système de canalisation fermé de section droite généralement circulaire, destiné à la mise en place par tirage ou au remplacement des conducteurs ou des câbles isolés dans les installations électriques ou de télécommunication
Source: 826-06-03 MOD
[IEV number 442-02-03]См. также пластмассовые трубы для электропроводок
См. также стальные трубы для электропроводок
4.1. Для прокладки проводов и кабелей необходимо применять специальные трубы для электропроводок: гладкие из непластифицированного ПВХ по ТУ 6-19-215-86, прил. 2; гладкие из вторичного ПЭ по ТУ 63.178-103-85, прил. 3; гладкие из наполненного ПЭ по ТУ 6-19-051-575-85, прил. 4; гофрированные из НПВХ по ТУ 6-19-051-419-84, прил. 5; гофрированные из ПЭ по ТУ 6-19-051-518-87, прил.6; гофрированные из вторичного ПЭ по ТУ 63.178-117-87, прил.7. При отсутствии указанных труб применяют технологические трубы: гладкие напорные из НПВХ по ТУ 6-19-231-87, прил.8; гладкие напорные из ПЭ низкого и высокого давления по ГОСТ 18599-83, прил. 9; гладкие из ПП по ТУ 38-102-100-76, прил. 10; трубы из вторичного ПЭ по ТУ 6-19-133-79, прил. П.
...
4.3. Применяют также трубы стальные электросварные по ГОСТ 10704-76 сортамент, прил. 12, легкие и обыкновенные водогазопроводные по ГОСТ 3262-75*, прил.13.[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]
Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- электропроводка, электромонтаж
Синонимы
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > труба для электропроводки
-
8 труба для электропроводки
труба
Компонентзащищеннойтрубной электропроводки, имеющий, как правило, круглое поперечное сечение, предназначенный для прокладки изолированных проводов и(или) кабелей в электрических или коммуникационных установках, допускающий их затяжку в него и(или) их замену.
ПримечаниеСоединения труб должны быть достаточно плотными, чтобы изолированные провода и (или) кабели могли быть только затянуты, но не введены сбоку в просвет между трубами.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60050-826-2009]
трубопроводтруба
Закрытый элемент кабельной конструкцииКомпонент трубной электропроводки круглого или иного сечения для прокладки в электрических установках кабелей и/или изолированных проводови/или кабелей в электрических установках,позволяющий производить ихвыемкузатяжку и/или замену.
Примечание
Трубопроводы должны быть закрыты таким образом, чтобы имелась возможность вставлять в них изолированные провода и/или кабели.
Трубы должны располагаться достаточно близко друг от друга, так чтобы отсутствовала возможность затянуть изолированные провода и (или) кабели в просвет между ними.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
conduit
a part of a closed wiring system of generally circular cross section for insulated conductors and/or cables in electrical or communication installations, allowing them to be drawn in and/or replaced
Source: 826-06-03 MOD
[IEV number 442-02-03]
conduit
part of a closed wiring system of circular or non-circular cross-section for insulated conductors and/or cables in electrical installations, allowing them to be drawn in and/or replaced
NOTE Conduits should be sufficiently close-jointed so that the insulated conductors and/or cables can only be drawn in and not inserted laterally.
[IEV 826-06-03]
[IEC 60204-1-2006]
raceway
A tube that encloses and protects electric wires.
[ http://www.answers.com/topic/raceway]FR
conduit
élément d'un système de canalisation fermé de section droite généralement circulaire, destiné à la mise en place par tirage ou au remplacement des conducteurs ou des câbles isolés dans les installations électriques ou de télécommunication
Source: 826-06-03 MOD
[IEV number 442-02-03]См. также пластмассовые трубы для электропроводок
См. также стальные трубы для электропроводок
4.1. Для прокладки проводов и кабелей необходимо применять специальные трубы для электропроводок: гладкие из непластифицированного ПВХ по ТУ 6-19-215-86, прил. 2; гладкие из вторичного ПЭ по ТУ 63.178-103-85, прил. 3; гладкие из наполненного ПЭ по ТУ 6-19-051-575-85, прил. 4; гофрированные из НПВХ по ТУ 6-19-051-419-84, прил. 5; гофрированные из ПЭ по ТУ 6-19-051-518-87, прил.6; гофрированные из вторичного ПЭ по ТУ 63.178-117-87, прил.7. При отсутствии указанных труб применяют технологические трубы: гладкие напорные из НПВХ по ТУ 6-19-231-87, прил.8; гладкие напорные из ПЭ низкого и высокого давления по ГОСТ 18599-83, прил. 9; гладкие из ПП по ТУ 38-102-100-76, прил. 10; трубы из вторичного ПЭ по ТУ 6-19-133-79, прил. П.
...
4.3. Применяют также трубы стальные электросварные по ГОСТ 10704-76 сортамент, прил. 12, легкие и обыкновенные водогазопроводные по ГОСТ 3262-75*, прил.13.[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]
Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- электропроводка, электромонтаж
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > труба для электропроводки
-
9 газоизолированная линия электропередачи
газоизолированная линия электропередачи
Линия электропередачи, токоведущие части которой заключены в металлический кожух, заполненный изолирующим газом.
[ ГОСТ 24291-90]EN
gas insulated line
gas insulated circuit (deprecated)
GIC (deprecated)
an electric line whose conductors are contained in a enclosure and insulated with a compressed gas
[IEV number 601-03-06]FR
ligne à isolation gazeuse
ligne électrique dont les conducteurs sont placés dans une enceinte et isolés par un gaz sous pression
NOTE – Le sigle CIG est à déconseiller.
[IEV number 601-03-06]Тематики
EN
DE
- Gassisolirte Leitung
- Leitung, gasisolierte
FR
53 газоизолированная линия электропередачи
Линия электропередачи, токоведущие части которой заключены в металлический кожух, заполненный изолирующим газом
601-03-06
de Gassisolirte Leitung
en gas insulated line
fr ligne à isolation gazeuse
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-английский словарь нормативно-технической терминологии > газоизолированная линия электропередачи
-
10 газоизолированная линия электропередачи
- Leitung, gasisolierte
- Gassisolirte Leitung
газоизолированная линия электропередачи
Линия электропередачи, токоведущие части которой заключены в металлический кожух, заполненный изолирующим газом.
[ ГОСТ 24291-90]EN
gas insulated line
gas insulated circuit (deprecated)
GIC (deprecated)
an electric line whose conductors are contained in a enclosure and insulated with a compressed gas
[IEV number 601-03-06]FR
ligne à isolation gazeuse
ligne électrique dont les conducteurs sont placés dans une enceinte et isolés par un gaz sous pression
NOTE – Le sigle CIG est à déconseiller.
[IEV number 601-03-06]Тематики
EN
DE
- Gassisolirte Leitung
- Leitung, gasisolierte
FR
53 газоизолированная линия электропередачи
Линия электропередачи, токоведущие части которой заключены в металлический кожух, заполненный изолирующим газом
601-03-06
de Gassisolirte Leitung
en gas insulated line
fr ligne à isolation gazeuse
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > газоизолированная линия электропередачи
-
11 газоизолированная линия электропередачи
газоизолированная линия электропередачи
Линия электропередачи, токоведущие части которой заключены в металлический кожух, заполненный изолирующим газом.
[ ГОСТ 24291-90]EN
gas insulated line
gas insulated circuit (deprecated)
GIC (deprecated)
an electric line whose conductors are contained in a enclosure and insulated with a compressed gas
[IEV number 601-03-06]FR
ligne à isolation gazeuse
ligne électrique dont les conducteurs sont placés dans une enceinte et isolés par un gaz sous pression
NOTE – Le sigle CIG est à déconseiller.
[IEV number 601-03-06]Тематики
EN
DE
- Gassisolirte Leitung
- Leitung, gasisolierte
FR
53 газоизолированная линия электропередачи
Линия электропередачи, токоведущие части которой заключены в металлический кожух, заполненный изолирующим газом
601-03-06
de Gassisolirte Leitung
en gas insulated line
fr ligne à isolation gazeuse
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > газоизолированная линия электропередачи
-
12 система кабельных коробов
система кабельных коробов
Система замкнутых оболочек, состоящих из основания (корпуса) и съемной крышки, предназначенная дляполного заключения в себяпрокладки внутри неё изолированных проводов, кабелей, шнуров и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60050-826-2009]
система кабельных коробов
Система замкнутых оболочек, состоящих из корпуса со съемной или открывающейся крышкой, предназначенная для прокладки внутри нее изолированных проводов, кабелей и шнуров и/или для размещения другого электрооборудования.
[ ГОСТ Р МЭК 61084-1 2007]
кабельнесущая система
Система закрытых оболочек, допускающая размещение изолированных проводов на базе подвижных поверхностей и предназначенная для полной защиты изолированных проводов, кабелей, шнуров, а также для размещения другого электрооборудования.
система кабельных коробов
Система закрываемых полых конструкций, состоящая из основания (корпуса) и съемной крышки, предназначенная для прокладки внутри них и защиты от механических повреждений кабелей, шнуров, изолированных проводов и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
cable trunking system
a system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electrical accessories
Source: 826-06-04 MOD
[IEV number 442-02-34]
cable trunking system
system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electric equipment including information technology equipment
Source: 442-02-34 MOD
[IEV number 826-15-04]
[IEC 60204-1-2006]FR
système de goulottes
ensemble d'enveloppes fermées munies d'un fond avec un couvercle amovible et destiné à la protection complète de conducteurs isolés et de câbles, ou au logement d'autre petit appareillage électrique
Source: 826-06-04 MOD
[IEV number 442-02-34]
système de goulottes, m
ensemble d'enveloppes fermées, munies d'un fond avec un couvercle amovible et destiné à la protection complète des conducteurs isolés et des câbles et/ou au logement d'autres matériels électriques y compris des matériels de traitement de l'information
Source: 442-02-34 MOD
[IEV number 826-15-04]Обратите внимание!
Различают два вида систем кабельных коробов:
1) (просто) система кабельных коробов (cable trunking system) - система любого сечения, но обязательно с крышкой;
2) система специальных кабельных коробов (cable ducting system) - система некруглого сечения и без крышек.
Примечание. В ПУЭ короб без крышки называется глухой короб (см. кабельный короб)
[Автор карточки]
Параллельные тексты EN-RU
Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base.
[Legrand/Wiremold. SECTION 16130 RACEWAY AND BOXES]В состав поставки входят специальные (глухие) кабельные короба, а также кабельные короба, состоящие из основания и защелкивающейся крышки, или из основания и двух защелкивающихся крышек.
[Перевод Интент]
1 - Система кабельных коробов
Система кабельных коробов
Система кабельных коробов
Недопустимые, нерекомендуемые
Примечание(1) - мнение автора карточкиТематики
- изделие электромонтажное
- электропроводка, электромонтаж
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > система кабельных коробов
-
13 система кабельных коробов
система кабельных коробов
Система замкнутых оболочек, состоящих из основания (корпуса) и съемной крышки, предназначенная дляполного заключения в себяпрокладки внутри неё изолированных проводов, кабелей, шнуров и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60050-826-2009]
система кабельных коробов
Система замкнутых оболочек, состоящих из корпуса со съемной или открывающейся крышкой, предназначенная для прокладки внутри нее изолированных проводов, кабелей и шнуров и/или для размещения другого электрооборудования.
[ ГОСТ Р МЭК 61084-1 2007]
кабельнесущая система
Система закрытых оболочек, допускающая размещение изолированных проводов на базе подвижных поверхностей и предназначенная для полной защиты изолированных проводов, кабелей, шнуров, а также для размещения другого электрооборудования.
система кабельных коробов
Система закрываемых полых конструкций, состоящая из основания (корпуса) и съемной крышки, предназначенная для прокладки внутри них и защиты от механических повреждений кабелей, шнуров, изолированных проводов и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
cable trunking system
a system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electrical accessories
Source: 826-06-04 MOD
[IEV number 442-02-34]
cable trunking system
system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electric equipment including information technology equipment
Source: 442-02-34 MOD
[IEV number 826-15-04]
[IEC 60204-1-2006]FR
système de goulottes
ensemble d'enveloppes fermées munies d'un fond avec un couvercle amovible et destiné à la protection complète de conducteurs isolés et de câbles, ou au logement d'autre petit appareillage électrique
Source: 826-06-04 MOD
[IEV number 442-02-34]
système de goulottes, m
ensemble d'enveloppes fermées, munies d'un fond avec un couvercle amovible et destiné à la protection complète des conducteurs isolés et des câbles et/ou au logement d'autres matériels électriques y compris des matériels de traitement de l'information
Source: 442-02-34 MOD
[IEV number 826-15-04]Обратите внимание!
Различают два вида систем кабельных коробов:
1) (просто) система кабельных коробов (cable trunking system) - система любого сечения, но обязательно с крышкой;
2) система специальных кабельных коробов (cable ducting system) - система некруглого сечения и без крышек.
Примечание. В ПУЭ короб без крышки называется глухой короб (см. кабельный короб)
[Автор карточки]
Параллельные тексты EN-RU
Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base.
[Legrand/Wiremold. SECTION 16130 RACEWAY AND BOXES]В состав поставки входят специальные (глухие) кабельные короба, а также кабельные короба, состоящие из основания и защелкивающейся крышки, или из основания и двух защелкивающихся крышек.
[Перевод Интент]
1 - Система кабельных коробов
Система кабельных коробов
Система кабельных коробов
Недопустимые, нерекомендуемые
Примечание(1) - мнение автора карточкиТематики
- изделие электромонтажное
- электропроводка, электромонтаж
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > система кабельных коробов
-
14 система кабельных коробов
система кабельных коробов
Система замкнутых оболочек, состоящих из основания (корпуса) и съемной крышки, предназначенная дляполного заключения в себяпрокладки внутри неё изолированных проводов, кабелей, шнуров и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60050-826-2009]
система кабельных коробов
Система замкнутых оболочек, состоящих из корпуса со съемной или открывающейся крышкой, предназначенная для прокладки внутри нее изолированных проводов, кабелей и шнуров и/или для размещения другого электрооборудования.
[ ГОСТ Р МЭК 61084-1 2007]
кабельнесущая система
Система закрытых оболочек, допускающая размещение изолированных проводов на базе подвижных поверхностей и предназначенная для полной защиты изолированных проводов, кабелей, шнуров, а также для размещения другого электрооборудования.
система кабельных коробов
Система закрываемых полых конструкций, состоящая из основания (корпуса) и съемной крышки, предназначенная для прокладки внутри них и защиты от механических повреждений кабелей, шнуров, изолированных проводов и (или) для размещения другого электрического оборудования, включая оборудование информационных технологий.
[ ГОСТ Р МЭК 60204-1-2007]
Примечание. Синим цветом обозначен вариант, предлагаемый автором карточки.EN
cable trunking system
a system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electrical accessories
Source: 826-06-04 MOD
[IEV number 442-02-34]
cable trunking system
system of closed enclosures comprising a base with a removable cover, intended for the complete surrounding of insulated conductors, cables, cords and/or for the accommodation of other electric equipment including information technology equipment
Source: 442-02-34 MOD
[IEV number 826-15-04]
[IEC 60204-1-2006]FR
système de goulottes
ensemble d'enveloppes fermées munies d'un fond avec un couvercle amovible et destiné à la protection complète de conducteurs isolés et de câbles, ou au logement d'autre petit appareillage électrique
Source: 826-06-04 MOD
[IEV number 442-02-34]
système de goulottes, m
ensemble d'enveloppes fermées, munies d'un fond avec un couvercle amovible et destiné à la protection complète des conducteurs isolés et des câbles et/ou au logement d'autres matériels électriques y compris des matériels de traitement de l'information
Source: 442-02-34 MOD
[IEV number 826-15-04]Обратите внимание!
Различают два вида систем кабельных коробов:
1) (просто) система кабельных коробов (cable trunking system) - система любого сечения, но обязательно с крышкой;
2) система специальных кабельных коробов (cable ducting system) - система некруглого сечения и без крышек.
Примечание. В ПУЭ короб без крышки называется глухой короб (см. кабельный короб)
[Автор карточки]
Параллельные тексты EN-RU
Raceways shall be one- or two-piece design with base and snap-on cover, or three-piece design with base and two snap-on covers which snap side by side on a common base.
[Legrand/Wiremold. SECTION 16130 RACEWAY AND BOXES]В состав поставки входят специальные (глухие) кабельные короба, а также кабельные короба, состоящие из основания и защелкивающейся крышки, или из основания и двух защелкивающихся крышек.
[Перевод Интент]
1 - Система кабельных коробов
Система кабельных коробов
Система кабельных коробов
Недопустимые, нерекомендуемые
Примечание(1) - мнение автора карточкиТематики
- изделие электромонтажное
- электропроводка, электромонтаж
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > система кабельных коробов
-
15 кабельная линия электропередачи
кабельная линия электропередачи
Линия электропередачи, выполненная одним или несколькими кабелями, уложенными непосредственно в землю, кабельные каналы, трубы, на кабельные конструкции.
[ ГОСТ 24291-90]
линия электропередачи кабельная
Линия электропередачи, состоящая из одного или нескольких параллельных электрических кабелей
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
кабельная линия электропередачи
КЛ
Линия для передачи электроэнергии или отдельных импульсов ее, состоящая из одного или нескольких параллельных кабелей с соединительными, стопорными и концевыми муфтами (заделками) и крепежными деталями, а для маслонаполненных кабельных линий, кроме того, с подпитывающими аппаратами и системой сигнализации давления масла.
[ Правила технической эксплуатации электроустановок потребителей]EN
underground cable
an electric line with insulated conductors buried directly in the ground, or laid in cable ducts, pipes, troughs, etc
NOTE – The same expression is used to describe the item physically.
[IEV number 601-03-05]FR
ligne souterraine
ligne électrique à conducteurs isolés disposée dans le sol, soit directement enterrée, soit placée dans une galerie, des tuyaux, des caniveaux, etc
[IEV number 601-03-05]Тематики
Синонимы
- КЛ
EN
DE
FR
52 кабельная линия электропередачи; КЛ
Линия электропередачи; выполненная одним или несколькими кабелями, уложенными непосредственно в землю, кабельные каналы, трубы, на кабельные конструкции
601-03-05
de Kabel
en underground cable
fr ligne souterraine
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > кабельная линия электропередачи
-
16 кабельная линия электропередачи
кабельная линия электропередачи
Линия электропередачи, выполненная одним или несколькими кабелями, уложенными непосредственно в землю, кабельные каналы, трубы, на кабельные конструкции.
[ ГОСТ 24291-90]
линия электропередачи кабельная
Линия электропередачи, состоящая из одного или нескольких параллельных электрических кабелей
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
кабельная линия электропередачи
КЛ
Линия для передачи электроэнергии или отдельных импульсов ее, состоящая из одного или нескольких параллельных кабелей с соединительными, стопорными и концевыми муфтами (заделками) и крепежными деталями, а для маслонаполненных кабельных линий, кроме того, с подпитывающими аппаратами и системой сигнализации давления масла.
[ Правила технической эксплуатации электроустановок потребителей]EN
underground cable
an electric line with insulated conductors buried directly in the ground, or laid in cable ducts, pipes, troughs, etc
NOTE – The same expression is used to describe the item physically.
[IEV number 601-03-05]FR
ligne souterraine
ligne électrique à conducteurs isolés disposée dans le sol, soit directement enterrée, soit placée dans une galerie, des tuyaux, des caniveaux, etc
[IEV number 601-03-05]Тематики
Синонимы
- КЛ
EN
DE
FR
52 кабельная линия электропередачи; КЛ
Линия электропередачи; выполненная одним или несколькими кабелями, уложенными непосредственно в землю, кабельные каналы, трубы, на кабельные конструкции
601-03-05
de Kabel
en underground cable
fr ligne souterraine
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
36. Кабельная линия электропередачи
КЛ
E. Underground cable
F. Ligne souterraine
Источник: ГОСТ 19431-84: Энергетика и электрификация. Термины и определения оригинал документа
Русско-английский словарь нормативно-технической терминологии > кабельная линия электропередачи
-
17 кабельная линия электропередачи
кабельная линия электропередачи
Линия электропередачи, выполненная одним или несколькими кабелями, уложенными непосредственно в землю, кабельные каналы, трубы, на кабельные конструкции.
[ ГОСТ 24291-90]
линия электропередачи кабельная
Линия электропередачи, состоящая из одного или нескольких параллельных электрических кабелей
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
кабельная линия электропередачи
КЛ
Линия для передачи электроэнергии или отдельных импульсов ее, состоящая из одного или нескольких параллельных кабелей с соединительными, стопорными и концевыми муфтами (заделками) и крепежными деталями, а для маслонаполненных кабельных линий, кроме того, с подпитывающими аппаратами и системой сигнализации давления масла.
[ Правила технической эксплуатации электроустановок потребителей]EN
underground cable
an electric line with insulated conductors buried directly in the ground, or laid in cable ducts, pipes, troughs, etc
NOTE – The same expression is used to describe the item physically.
[IEV number 601-03-05]FR
ligne souterraine
ligne électrique à conducteurs isolés disposée dans le sol, soit directement enterrée, soit placée dans une galerie, des tuyaux, des caniveaux, etc
[IEV number 601-03-05]Тематики
Синонимы
- КЛ
EN
DE
FR
52 кабельная линия электропередачи; КЛ
Линия электропередачи; выполненная одним или несколькими кабелями, уложенными непосредственно в землю, кабельные каналы, трубы, на кабельные конструкции
601-03-05
de Kabel
en underground cable
fr ligne souterraine
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
36. Кабельная линия электропередачи
КЛ
E. Underground cable
F. Ligne souterraine
Источник: ГОСТ 19431-84: Энергетика и электрификация. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > кабельная линия электропередачи
См. также в других словарях:
electric motor — motor (def. 4). [1885 90] * * * Introduction any of a class of devices that convert electrical energy to mechanical energy, usually by employing electromagnetic phenomena. Most electric motors develop their mechanical torque by the… … Universalium
electric generator — ▪ instrument Introduction also called dynamo, any machine that converts mechanical energy to electricity for transmission and distribution over power lines to domestic, commercial, and industrial customers. Generators also produce the… … Universalium
Electric power distribution — … Wikipedia
Electric motor — For other kinds of motors, see motor (disambiguation). For a railroad electric engine, see electric locomotive. Various electric motors. A 9 volt PP3 transistor battery is in the center foreground for size comparison. An electric motor converts… … Wikipedia
Electric shock — Electrocute redirects here. For the band, see Electrocute (band). An electric shock can occur upon contact of a human s body with any source of voltage high enough to cause sufficient current through the muscles or hair. The minimum current a… … Wikipedia
Electric vehicle — Sustainable energy Renewable energy … Wikipedia
Mineral-insulated copper-clad cable — MIMS redirects here. For multi isotope imaging mass spectrometry, see Isotope mass spectrometry. PVC sheathed MICC cable. Conductor cross section area is 1.5 mm²; overall diameter is 7.2 mm … Wikipedia
List of Tesla patents — Below is a list of Tesla patents. Dr. Nikola Tesla was an inventor who obtained around 300 patents [Snezana Sarbo, [http://www.tesla symp06.org/papers/Tesla Symp06 Sarboh.pdfNikola Tesla s Patents] , Sixth International Symposium Nikola Tesla,… … Wikipedia
History of electromagnetism — The history of electromagnetism, that is the human understanding and recorded use of electromagnetic forces, dates back over two thousand years ago, see Timeline of electromagnetism. The ancients must have been acquainted with the effects of… … Wikipedia
electromagnetism — /i lek troh mag ni tiz euhm/, n. 1. the phenomena associated with electric and magnetic fields and their interactions with each other and with electric charges and currents. 2. Also, electromagnetics. the science that deals with these phenomena.… … Universalium
Knob and tube wiring — (sometimes abbreviated K T) was an early standardized method of electrical wiring in buildings, in common use in North America from about 1880 to the 1930s. [Terrell Croft and Wilford Summers (ed), American Electricans Handbook, Eleventh Edition … Wikipedia